Flooring material needs to be practical, hard wearing and hygienic, especially if it’s being used in high traffic areas or a building like a hospital or a school. Even the most hard-wearing material will need to be repaired, maintained or replaced from time to time and it’s essential to have the right equipment for the job. 

A floor grinder is a highly useful piece of machinery that can be used for both DIY and commercial applications. This machine can be used for a variety of projects but it’s important to make sure you know what you’re doing, especially if you’re using a floor grinder for the first time. If you’re thinking about floor grinder rental and want to know more about this machine and how to use it, see below for our handy guide. 

What is a floor grinder?

A floor grinder is a machine which uses rotating discs to clean, polish, smooth or resurface flooring. They’re commonly used on concrete flooring but they can also be used on hardwood or stone floors. Floor grinders can be used to prepare a floor (by removing leftover adhesive, paint or glue, or levelling the surface), or they can be used to polish and finish the floor to a high shine. 

Floor grinders are available in walk behind or ride-on models, as well as smaller, handheld grinders. 

How does a floor grinder work? 

Floor grinding machines all work in roughly the same way, although there is a difference in their quality, power and abilities. Abrasive pads on the bottom of the machine grind off the top surface of the floor, helping to level it out or remove surface level blemishes. Some floor grinders use slightly different pads to clean and polish the floor and give it a shiny, reflective surface. 

An operator moves the machine over the surface of the floor in a smooth, even motion, while discs underneath spin around. Each disc holds a pad which grinds or polishes the floor (depending on the pad material). Floor grinders can have just one disc, or as many as six working at once.

Diamond-coated discs and diamond blades are common abrasives used in floor grinding machines. They’re available in a range of grits ranging from coarse to fine and it’s important to select the right level for the job (more on this later). 

Floor grinders can be used in both wet and dry conditions depending on their application. Wet floor grinders use water to cool down the diamond pads and remove excess dust. Water helps to reduce friction and increase the lifespan of your machine, but it can be quite messy to work with. 

If you’re using the dry method, the machine will polish the floor while containers within the grinder remove and store the dust. Both methods are often used for best practice; the dry method will remove any imperfections or uneven sections of flooring and the wet method can polish the floor to give an attractive finish. 

Major applications which require floor grinders

Floor grinders are versatile machines that can be used for a variety of different applications. We’ll explore some of the most common uses in more detail below. 

Floor grinding and levelling 

This application is most commonly used on concrete floors, as the surface must be properly prepared before repainting or adding a coating. Floor grinders can be used to level the floor and smooth away any inconsistencies or damage in the floor’s surface or edges. Coarse diamond discs will be needed for this application and you may need to go over the surface several times to achieve your desired result. 


Once a floor has been prepped and made level, it can then be polished to a high shine. Different discs may need to be used during the polishing process, with a move towards finer abrasives with each polish. Floor polishing is highly effective and it gives an attractive, mirror-like shine to surfaces such as concrete. 

Hardwood flooring applications

Floor grinders can also be used to smooth and refinish hardwood floors. Grinders remove the top layer of flooring to reveal the fresh wood underneath and this can then be treated with a new wood stain or fresh layer of sealant. 

It’s recommended that you refinish hardwood flooring every seven to 10 years and grinders allow you to remove any scratches, dents or stains on the surface of the wood. They also remove any traces of old varnish and allow you to change the colour of the stain if required. 

Stone flooring applications 

Floor grinders are ideal for use on concrete but they can also be used on other stone flooring materials, such as marble or granite. Floor grinding can change and restore the appearance of stone flooring by levelling the surface, preparing the surface for treatment or polishing the stone to a reflective shine. 

Screed removal

Screed is often confused with concrete, but there are differences in the finish, the size of aggregates used and the mix consistency. Screed is poured as a thin layer to create a smooth coating on a floor and it’s often found underneath tiles. When renovating or repairing a floor, you may need to remove an old layer of screed first. This can be done using a floor grinder, which will grind down the top layer until the screed is gone. 

Paint, latex and adhesive removal

If you’re replacing flooring like carpet, vinyl tiles or rubber, you’ll first need to use a stripping machine to remove the existing flooring. Once this is done, it’s likely that they’ll be some adhesive, latex or paint left behind. Concrete flooring may also have some patches of an existing coating that will need to be removed before repainting or resealing. 

If you need to remove paint, latex or adhesive from a floor, you can do so using a floor grinding machine. They provide a chemical-free way to remove any existing paint or coatings and ensure the floor is prepared for the next stage. 

How to use your floor grinder effectively

Floor grinders are versatile and powerful machines, but it’s important to know how to use your grinder effectively. This will make the job much easier and give you the required finish you’re after. 

Pick the right diamonds 

Choosing the right diamond pads is crucial to achieve your desired finish. You may have to experiment with a few different types but it’s worth doing as much research as you can beforehand. This includes understanding different bonds and segment styles, as well as testing the concrete hardness if possible.

You’ll also need to think about whether you’re removing material (like glue or screed) and if you’ll be polishing the floor afterwards. Diamonds that are too abrasive could scratch the floor beyond repair, so always consult a professional if you’re unsure. 

Don’t rush 

You’ll achieve the best results if you take your time and don’t rush, especially if you’re removing stubborn patches of adhesive or paint. Rushing means that you might have to go over the same area multiple times, which then takes more time in the long run! Go slowly and carefully, especially around the edges of the floor. 

Make sure there’s adequate power

Some larger grinders require more than household power. You may need a generator or have to consult an electrician to make sure there’s adequate power before the work begins. This is especially important if you’re using a floor grinder for a DIY job at home. 

Concept Flooring Technology – The Specialists in Floor Grinding Equipment Hire

If you’re looking to hire a floor grinder for your next project, get in touch with the experts at Concept Flooring Technology. We’re proud to offer a range of high quality flooring machines for hire, including floor grinders, concrete floor polishers, handheld grinders and preparation grinders. 

Our machines are suitable for a wide range of applications, from re-levelling a concrete floor, to polishing, tile stripping or removing existing paints, latex or coatings. Our floor grinding equipment is available for hire nationwide and we aim to offer next day delivery for all customers. Unsure about which floor machine is right for you? Give us a call today to speak to our friendly, knowledgeable team, or contact us online.

Whether you’re grinding or stripping your flooring, maintaining a safe environment is essential. However, one area that is often overlooked is dust extraction. Removing dust and debris is important in the floor preparation process, not only for your health but in creating an efficient work site.

Here’s why dust extraction is important.

Reduces health-related risks

Perhaps the most important reason for hiring dust extraction equipment is your improved health and safety. Dust may seem harmless, but even a small amount can cause respiratory issues if you don’t have the right precautions in place. Extraction equipment will reduce the amount of dust in the air and therefore, the amount you breathe in including harmful particles that are released from particular materials.

Better working conditions

Using any type of equipment requires a steady hand and concentration. If your workspace is filled with dust, this can affect your productivity and the quality of your work. Alternatively, dust extractors operate alongside your equipment so dust is extracted while you work. 

Keep your machinery operating efficiently

Keeping dust at bay is beneficial for your health as well as staying productive. Leaving dust and debris to buildup is a surefire way of clogging up your machinery and over time this will affect its performance. Using a dust extractor is a simple yet effective way of overcoming this problem so you can spend more time getting on with your project and less time avoiding repairs.

Meeting safety guidelines

If you’re hiring flooring equipment for your team then it’s your responsibility to ensure that your setup is safe. Dust will lower the air quality so it needs to be managed effectively, plus nobody wants to work in an unbearable environment. Hiring dust extraction equipment alongside your flooring machines will minimise high-risk materials such as asbestos and lead causing problems and ensure that you’re in line with safety guidelines.

At Concept Flooring Technology, we have a wide range of flooring machinery available for hire as well as suitable dust extractors. Safety should always be a top priority while operating our machinery, which is why our knowledgeable team will help you find the right equipment for the job. Get in touch with us today for more information.

When hiring flooring machinery it’s important to consider the safety aspect of your project. Do you have an appropriate PPE? A risk assessment should be done beforehand to determine which PPE is required or get expert advice from our team who will guide you through the necessary safety steps and precautions.

In this blog, we explain some of the most essential PPE that you may need. 

Ear protection

Using flooring machines can be a noisy job. To keep your ears protected, ear defenders, ear muffs or ear buds will cut down the pressure on your eardrum and muffle the sound. If you’re using machinery all day without protection, this can result in problems such as tinnitus or infections.

Safety footwear

When using walk-behind machines you must wear the right kind of footwear. Open toe shoes put your feet at risk of injury whereas safety footwear, such as boots, will shield your toes. If you accidentally catch your foot while operating or drop a handheld machine, your feet will be better protected.

Protective clothing

There are many ways of keeping your skin injury-free while using flooring machinery, especially handheld machines. Firstly, full-length trousers will cover your legs or overalls will shield your entire body from debris and machine parts – you should also avoid hoodie cords that can get easily caught. 


Similarly to covering your feet, your hands also require protection. Invest in a pair of gloves to shield your fingers and forearms from hazards as well as prevent blisters.

Face mask

Respiratory PPE helps to protect the entire internal respiratory system and stops anything from entering the mouth. By filtering out dust and debris, you will avoid breathing in harmful particles so you’ll remain safe while operating your machinery. Plus, the mask protects the outside of the mouth and face.


If your visibility is impaired, this can affect your handling and therefore cause accidents on site. Always keep your eyes protected by wearing goggles, face shields or visors. Your eyes are very delicate and even the smallest fleck of dust can cause irritation so don’t be tempted to go without eye protection.

Are you renovating your commercial flooring? At Concept Flooring Technology, we have a wide range of machines available for hire including grinders, stripping machines and dust extractors. Our professional team will help set up and provide a demonstration if needed, so your machine is ready to go! Get in touch with us today for more information.

Renovating your commercial premises is a great way of breathing new life into the space including upgrading your flooring. Soft floor removal, for flooring such as carpet, vinyl and rubber, will make the removal easy so you’ll have your new floor covering installed in no time!

Here’s all you need to know about soft floor removal.

What kind of flooring requires soft floor removal?

Soft flooring includes several different types of floor coverings that are usually manufactured as a roll or as flexible tiles, such as:

  • Carpet
  • LVT
  • Vinyl
  • Rubber
  • Cork

In most cases, soft flooring can be removed in a few simple steps with help from a commercial floor stripping machine. 

Is soft flooring easy to remove?

How quickly your soft flooring can be removed will depend on the materials. For example, rubber flooring that has been glued down can be difficult to lift and thicker flooring may take a little more time to remove. However, by hiring the right equipment you’ll be in the best position to start your soft flooring removal and achieve the results you’re looking for. Generally speaking, soft flooring is easier to remove than concrete and other similar materials.

Why should you hire a floor stripper machine?

As the name suggests, floor strippers are designed to strip flooring so you have a clear surface to lay a new floor covering. There are different models to choose from depending on the size of the area such as walk-behind strippers for small spaces and ride-on strippers for large rooms. 

Each stripper has a sharp vibrating blade, which can be adjusted to suit different flooring types, that cuts through and lifts the soft flooring. 

Do you need a reliable floor stripping machine? At Concept Flooring Technology, we offer walk-behind and ride-on floor stripping machines available for hire. All models are powerful and provide rapid removal, whilst all are compact and able to fit through a standard doorway. We can offer advice on all machines to hire, as well as which consumables will be best to achieve your required finish. – find out more today.

A floor scabbler, also known as floor planers and scarifiers, is a walk-behind device that is mainly used on concrete surfaces. These machines are most suitable for reducing the height of a concrete slab, thick adhesive or to provide a textured finish.

Here’s an explanation as to how they work, why they’re useful, how to prepare to use them and who might benefit from hiring one!

How Do They Work?

Scabblers come in a variety of sizes and types that work along the same basic principle. They pound tungsten-tipped cutters into the concrete surface which breaks this layer down, allowing for it to be removed. This reveals a much rougher section of the concrete than the top layer as aggregate will now be exposed. This can be done to specific ‘grades’ which relates to how strong the concrete is. Plus, each machine has a height adjustment handle, depending on your requirements.

Why Are They Useful?

This is a useful tool as it allows for quick and effective removal. Rather than using a larger machine which may be cumbersome, the scabbler can be used to address specific imbalances quickly and efficiently. They are also suitable for bitumen removal in demolition projects as they don’t require smooth finishes.

It’s also useful as it exposes a rougher top surface of an aggregate which, depending on your purpose for the concrete floor, may be more ideal for bonding and adhesives. Along these lines, they may be used to create more grip on roads by giving them a rougher surface where they may have been worn down over the years.

Preparation for Use

It’s a good idea to adequately prepare your machine and surroundings before beginning to use your scabbler. For instance, you’ll want a tile-specific blade rather than a  carpet stripper if you’re using it on a swimming pool or tiled flooring. These steps will boost the efficiency of your operation, reducing the amount of time the equipment needs to be rented out.

Who Would Need Them?

Because they’re used to both remove materials and roughen surfaces, scabblers have a broad range of applications which make them a great choice for a number of sectors including:

  • Pools that need to reapply grout for tiles
  • Supermarkets and shopping malls
  • Most new build houses now use concrete flooring
  • Councils working on roads
  • Car parks
  • Construction and industrial sites

Here at Concept Flooring Technology, we aim to help our clients complete their projects to the highest of standards. We have a broad range of floor machines to hire, including scabblers, and we’d be more than happy to discuss your requirements with you and give you some recommendations. If you have any questions then don’t hesitate to get in touch with us by calling 01494 485952 today!

At Concept Flooring Technology, we offer a range of machines for hire including preparation grinders, planers and floor scabblers. But to keep your flooring looking clean and tidy, it’s important to maintain the upkeep of your floor which requires the use of scrubber dryer machines. The scrubber dryers we have available for hire are great machines and are ideal for a range of uses.

They work by rotating brushes on the floor’s surface in a scrubbing motion to remove dirt and residue from the floor, which is then collected by a vacuum to leave the floor clean and dry. Rather than purchasing a scrubber dryer, which can be somewhat costly, Concept Flooring Technology provides them for rental at a reasonable fee.

But why might you need to hire a scrubber dryer? Here are a few reasons it would be beneficial for your business.

Who needs scrubber dryer hire?

Many industrial and commercial premises would benefit from hiring a scrubber dryer to clean their flooring. If you have large areas of flooring that experience a high amount of footfall, you may consider hiring a scrubber dryer to stay on top of the hygiene and to maintain clean premises.

Some of these include:

  • Factories
  • Warehouses
  • Healthcare sites
  • Offices
  • Shops
  • Schools

The benefits of hiring a scrubber dryer

There are many reasons why it would be beneficial to hire a scrubber dryer. Read on to discover how to make your business safer, more hygienic and more economical.


Cleaning large premises can be a long and laborious process, leading to large areas of wet and slippery flooring. This creates a potentially hazardous area for a while after the cleaning has been completed. Many workplace accidents are caused by wet or contaminated floors, leading to personal injury claims against the business or organisation. This could be easily avoided by regular and efficient cleaning with a scrubber dryer.

Because a scrubber dryer vacuums up any water from the surface as it cleans, once the scrubber dryer has been over a section, it is already left dry and safe to walk on. This also allows you to clean more regularly without having to wait until customers or colleagues have left the premises. Regular cleaning will also reduce the risk of slipping on spills, as the hazardous area will be cleaned up quickly.


As businesses continue to adapt and evolve in tackling the changes to working life since COVID-19, workplaces must be kept as hygienic as possible, this certainly includes clean floors and surfaces. By doing so, this will help to maintain high standards of hygiene in the workplace. By ensuring a safe and clean workplace, you will be able to reduce the number of sick days and time off work that needs to be taken by employees. A scrubber dryer is an imperative machine to help keep the flooring clean throughout your building.

Not only this, but environments such as healthcare facilities have an utmost responsibility to keep their premises clean. If there is regular contamination of flooring with hazardous fluids, the floors must be cleaned thoroughly and regularly. The same also goes for the food and drink industry as it’s vital that you maintain a clean environment where people consume food and beverages. Essentially, it is important to keep a clean and safe work environment and this can be done with scrubber dryer hire.

More effective

If you need to clean large spaces with just a mop and bucket, you’ll be spending valuable time on a task that can be completed much faster with a scrubber dryer. By using a mop and bucket you may simply be spreading dirt across the floor rather than actually cleaning it, or even just diluting it with water. A mop and bucket will get dirty very quickly, and after several uses, will not be that effective at cleaning. You will end up spending more money on time and resources and whoever is in charge of cleaning large areas of flooring will probably tire much quicker than they would if they were using a scrubber dryer.

On the other hand, a scrubber dryer uses cleaning chemicals to break down and loosen dirt, grease and grime, dislodge the debris and shine the floor. After cleaning it then vacuums all the residue up so that nothing is left on the floor. As a result, you have expertly clean floors, while the machine does all the work.

Restore exceptionally dirty floors

It’s vital that you have a good hygiene procedure in place if your business or workplace is prone to high amounts of dirt, spills or heavy foot traffic. Regular cleaning can be time-consuming, especially if you need to deep clean your flooring every day. One of the key selling points of a scrubber dryer is how deeply it can clean floors as opposed to other cleaning equipment. It can thoroughly clean and remove any dirt and debris from flooring and grooves and vacuum any remaining dirt, leaving the floor clean and dry.

If your workplace, such as a warehouse or factory, gets exceptionally dirty, it’s worthwhile hiring a scrubber dryer to feel confident that the floors will be as clean as possible. This ensures high hygiene levels, a safe work environment and makes your business look desirable to any customers or clients that may come in.


There are many instances within a business where you can choose more sustainable options. Considering your water usage is something we can all be more aware of. A scrubber dryer has a more controlled usage of water and cleaning solution, making sure you only use as much as you need to get a great clean on your floor. By using a scrubber dryer you can clean a floor using a controlled amount of detergent and water, therefore being much kinder to the environment. For areas that may be more soiled than others, you’ll need to use more water and detergent than an area that only has light usage. A scrubber dryer will allow you to control how much water and detergent to use depending on how deep a clean you’ll need for a particular area.

Why use Concept Flooring Technology for your scrubber dryer rental?

If you’ve decided you would benefit from using a scrubber dryer in your premises, you may be wondering what the benefits are of hiring a machine as opposed to buying one outright. Besides the obvious financial benefits, hiring a scrubber dryer from Concept Flooring Technology offers you an efficient, hygienic and safe solution to cleaning your floors.

Here’s why you should hire from Concept Flooring Technology:

Access to industry-leading expertise and knowledge on floor grinders

Concept Flooring Technology has a wide range of machines available for hire and are experts in the industry. Any questions you may have, they will be able to answer and help you get the most out of the machines you hire. Whether you’re hiring stripping machines, planers, floor scabblers or scrubber dryers, they will be able to advise you on how to properly use them. Furthermore, they’ll be able to provide you with all the machines you’ll need to create great finished floors, including maintenance after the floor grinding is complete.

Exceptionally well-maintained machines

Concept Flooring Technology only hires out machines that have been very well-maintained, meaning you’ll be able to get your hands on great machinery to grind, scrabble, polish and clean your flooring. You can feel confident that the machine you hire will be of great quality and the best of its kind. This ensures your scrubber dryer will efficiently and effectively deep clean your floors.

Excellent customer service

The team at Concept Flooring Technology will do all they can to ensure your machine hire goes smoothly and the job is completed to a high standard. They can provide over the phone advice and on-site set-up and demonstrations to ensure you can competently use the machine. What’s more,  general wear and tear maintenance and PAT Testing is included in the service to ensure you only get the best products and value for money.

To find out more information, visit our website or call 01494 485952 to see how we can help you.

Here at Concept Flooring Technology, we have a fleet of flooring machines that we hire out. Seeing as they can look fairly similar and do fairly similar things, it can be difficult to understand the differences between these different options. This blog outlines these differences and exactly what use each machine is most optimal for.

1. Handheld Grinder

An angle grinder is essentially a motor that spins a disc around at a high speed. Depending on what type of blade is attached, this machine abrades different materials and wears them down. They’re not great for polishing as they have just one head but they’d be handy for accessing tricky spots like nooks, crannies and crevices.

2. Preparation Grinders

These work similarly to handheld grinders, just that they’re a larger walk-behind option. Whereas handheld options are better for smaller, more awkward areas, preparation grinders are better for covering large surfaces at a quick pace. Some models, like the HTC 400, use a number of diamond tool segments inside a single head rather than having multiple heads.

3. Polishing Finishing Grinders

Polishing finishing grinders are different because they’re always ‘planetary grinders’ which means that they have multiple rotating heads. This makes them capable of polishing surfaces and materials to a much finer degree than more aggressive abrasion techniques.

4. Planers and Scabblers

Planers and scabblers are also great options for removing materials quickly from a surface. Where they’re particularly unique is that they leave the new surface layer textured which prepares them much better for the installation of grout, glues and adhesives.

5. Stripping Machines

These machines are ideal for removing carpet, vinyl, ceramic tiles, and other floor coverings from your floor. A stripping blade thrusts under the material being removed, separating it from the floor it was attached to. However, it’s important that the appropriate attachment is used for the material being removed.

6. Cleaning Machines

Also known as scrubber driers, cleaning machines are used to ensure that the flooring you lay down is clean and presentable. Water is fed a brush and after getting any dirt, grime or debris off the floor, the machine vacuums up the remaining solution. Here at Concept Flooring Technology, we have both walk-behind and rideable options depending on your requirements.

If you have any further questions about these key flooring machines, or if you’d like to enquire about the different models we have and which might be most suitable for your project, then don’t hesitate to get in touch with us by calling 01494 485952 today!

Handheld grinders are versatile machines as they allow you to work in numerous areas and on different materials that otherwise wouldn’t be possible with larger planetary grinders. Given their usefulness in the construction field, it’s important that you understand how they work, what sort of blades are required, what sizes they come in and how to know when you’ll need replacements.

Here are all the answers you’ll need!

What Are Handheld Grinders?

Invented in 1954 in Germany, handheld grinders are handheld power tools used for grinding and abrasive cutting. They’re powered via an electric motor that drives a geared head, positioned at a right angle, which turns a disc at high speeds. This disk has a diamond blade attached to it which does the grinding.

Handheld grinders are used for areas that are particularly difficult to access. It could be that the floor of the room you wish to grind has a particularly tricky layout in one corner or that there’s a support structure in the middle of the space, around which it’s difficult to manoeuvre a larger machine. These scenarios are where handheld grinders are especially useful.

What Are Diamond Blades and How Are They Made?

Diamond blades are essential for the construction industry because of the durability of diamonds as a material, allowing for innovative applications like drilling and polishing. Diamond blades consist of a steel core along with diamond segments around the circumference of the disc. Synthetic diamond grit is combined with metal powder which is then sintered, meaning that these components are transformed into a solid coherent mass via heat and/or pressure.

What Sizes Are Available?

Diamond blades come in a range of sizes. Larger ones closer to 180mm are more suitable for stonemasons and flooring contractors. Alternatively, sizes closer to 100mm are better for detailed work and recesses. Here at Concept Flooring Technology, we stock 125mm and 180mm options so that we have all bases covered for our customers.

How Do I Know When My Diamond Blade is Dull?

You’ll know when the blade is getting dull because it’ll glaze over, indicating that the metal bond that holds the diamonds in place has melted over the diamonds. The blade will also appear to be smooth, showing that the diamonds have completely worn away.

How long they last is a difficult question to answer as it completely depends on the quality of the diamond blade as well as what type of material it’s used against. Generally, a 12 hour lifetime is considered ideal.

If you have any further questions about handheld grinders and their diamond blades, or if you’d like to know about some of our other services like hiring stripping, cleaning or preparation machines, then don’t hesitate to get in touch by calling us on 01494 485952 today!

Once you have achieved your desired flooring through scabbling, grinding, stripping and polishing, you’ll need to maintain it by using quality cleaning machines. If your flooring is subject to heavy footfall or spillages, hiring floor cleaning machines such as scrubber dryers or grout cleaning machines are an excellent solution to keep your flooring looking clean and shiny.

If you’re considering floor cleaner hire from Concept Flooring Technology, you may have some questions about how these machines work and how to use them. Here we’ll answer these questions so you can prepare yourself to hire a great floor cleaning machine such as a scrubber dryer or grout cleaning machine.

Frequently asked questions

Which types of machines are available?

At Concept Flooring Technology, we have two types of scrubber dryers available, these are ride-on or walk-behind machines. We stock Numatic scrubber dryers as they are some of the best floor cleaning machines on the market.

  • Numatic TT4045 Scrubber Dryer

This scrubber dryer is a heavy-duty walk-behind machine with a 40L capacity. It plugs into your mains power to offer a continuous and powerful clean, without interruption. You can choose how much solution is fed down through the heavy-duty scrubbing brush on the front of the machine. The curved vaccinated squeegee collects the slurry and deposits it into the 40L waste tank which can be emptied at a drain once you’ve finished cleaning.

  • Numatic TR0650 Scrubber Dryer

This machine is a ride-on scrubber dryer ideal for large areas. It’s battery-powered and holds 120L with 3.5 hours of running time so you can get large jobs done before it will need to be charged again. The advantage of battery-powered floor cleaning machines is that you don’t have a cable that could get caught on furniture or create a tripping hazard. This also means you are able to cover large spaces without needing to think about access to power cords or dealing with extension cords.

To determine which machine is best for you, consider what it will be used for. If you need to clean large areas with little access to power sources, the ride-on scrubber dryer may be beneficial. However, if you only need to clean smaller areas, the stand-behind will work well as you will have a constant power source.

How do scrubber dryers work?

A scrubber dryer is designed to perform two types of cleaning functions simultaneously – scrubbing from a rotary cleaning machine and drying from a vacuum-like suction operation. As the scrubber dryer passes across the floor, it cleans and vacuums, leaving a previously dirty floor clean and bone dry, allowing people to walk over it straight away. This makes them ideal for public and commercial facilities because they provide a safe, quick and hygienic solution to cleaning your flooring as opposed to a standard bucket and mop.

A scrubber dryer is made up of a clean water tank, a vacuum unit, a squeegee, a collection tank and a control panel. The clean water tank ranges in size depending on the size of the model. Also, a ride-on scrubber dryer will hold more water than a walk-behind machine. Water is fed from the tank directly through the brush heads and is used to clean through rotary scrubbing.

The vacuum unit is located within the collection tank. It’s protected from water thanks to a float valve which cuts off the vacuum operation in the event the wastewater level becomes too high. This is teamed up with a squeegee that sits on the back of the machine and follows behind it when the machine is moving. It is wider than the machine itself to help collect water when the machine turns. The water collected can be emptied through a drainage outlet below its base.

How do grout cleaning machines work?

Grout cleaning machines are ideal for cleaning grouts on granite setts, pavers, external pavements and pedestrian areas. They are able to deep clean the grout without pulling it up from the joints. The continuous sponge is fed through a water bucket and rollers, the excess sludge and water is squeezed out leaving the sponge to repeat the cycle. The roller can be easily replaced with a new sponge belt once it has become too dirty. As grout is liable to pick up dirt over time, it requires a bit more attention than your typical cleaning methods, particularly when covering a large area.

What consumables will I need?

Consumables are a part of a machine that needs to be replaced at a certain interval of time, based on the amount of wear and tear it has experienced. When hiring floor cleaning machines you may need to replace the consumables regularly as they can become worn and dirty. However, you won’t need to replace them nearly as often as standard cleaning materials such as sponges or mops.

For your scrubber dryer machine, scrubbing brushes are fitted to the machine. For the Numatic TT0650 scrubber dryer, you’ll need two 330mm brushes and for the TT4045, you’ll need one 450mm brush. The grout cleaning machines use sponge belts to clean.

What are the advantages of hiring a floor cleaning machine?

At Concept Flooring Technology, we hire out floor cleaning machines alongside other machines such as floor scabblers and grinding machines. If you’re on the fence about hiring or buying, there are many advantages to hiring a floor cleaning machine.

Hiring machinery from Concept Flooring Technology is more cost-effective because the machines we offer are of the most exceptional in the industry. Therefore making them a brilliant investment that a lot of businesses may not be able to otherwise afford. Hiring these machines is a much more affordable solution and you can get a higher quality machine for a lower cost.

When you hire a machine, the maintenance costs are not down to you. You won’t be expected to cover the costs of the typical degradation of a machine and at the end of your rental period, you can return the machine back to Concept Flooring Technology. This means you don’t need to worry about disposing of an old machine when you no longer need it. If you do choose to hire a machine through Concept Flooring Technology, the team will ensure that each piece of machinery is delivered with all the relevant paperwork including P.A.T certification, electrical or fuel safety sheets and hand-arm vibration information.  We will also provide nationwide delivery and collection with on-site set-up and demonstration.

Whether you intend to use floor cleaner hire machines on a short-term or long-term basis, hiring is a great option. You can choose how long you would like to hire the machine for, finding a contract that works for you. By hiring from Concept Flooring Technology, you can rest assured that the service you receive is first-rate. Concept Flooring Technology is a member of the Hire Association Europe, the industry-leading trade association for the plant and tool hire sector, within which we are SafeHire Accredited. This certification was developed as guidance of safety and quality agencies and is endorsed by the British Standards Institute.

Concept Flooring Technology: From scrubber dryers to concrete floor polishers

Whatever flooring machines you’re looking for, Concept Flooring Technology has a fantastic range of high-quality machines to help you get the job done. Whether you’re grinding concrete or keeping it looking spotless, we have the machine for you. We supply planers and floor scabblers, scrubber dryers, stripping machines, handheld grinders and preparation grinders as well as a number of consumables. We are happy to help advise you on the right machines to hire as well as how to properly use them. For more information, get in touch with our friendly team or call us on 01494 485952.

Have you found yourself feeling a little uncertain of what type of concrete floor grinder would be best suited to your specific needs? There are certainly a couple of things to consider prior to deciding which type you want to use. A concrete floor grinder can be utilised for lots of different applications varying from cleaning concrete floors to getting rid of concrete coatings to polishing concrete floors.

With this in mind, our mini-guide will talk you through three of the most popular and widely used varieties of concrete floor grinders and give you a breakdown of each one.

Handheld Floor Grinders

Handheld concrete grinders are the most widely used for edgework and hard to reach areas. Often utilised for floor grinding applications and polishing concrete countertops. Two of the most popular sizes tend to come between 4 – 5 inches and 7 – 9 inches. These are frequently used for the purpose of smoothing out rough patches on a concrete floor, surface preparation for coatings like epoxy, and for polishing concrete countertops.

Walk-behind Concrete Floor Grinder

These vary in size and you can get much smaller ones but also utilize a much larger model for a more substantial project. Walk-behind floor grinders also can be used for the purpose of covering a wider surface area. These particular floor grinding machines are ideal for quickly getting rid of coatings such as epoxy, paint, tile glue, mastic, and thin-set.

These can also be used to polish concrete floors in locations such as residential homes, commercial buildings and warehouses. Walk-behind floor grinders can come equipped with anything from 1 disc on the bottom up to 5 or 6 discs. Quite often this particular model proves to be very popular.

Ride-On Floor Grinder

This variety of floor grinder is often used to grind and polish commercial flooring so this could classify as anything from shopping centres, showrooms, distribution centres and warehouse floors. A ride-on floor grinder is able to grind and polish up to 5 feet wide in one pass, this is a key factor that enables this type of machine to produce a finished, smooth and glossy floor.

Do you need a concrete floor grinder? At Concept Flooring Technology, we provide a range of machines that deliver amazing results. Our concrete grinders and polishers are available in 110v, Three Phase and petrol which are all perfect options for all common diamond grinding and polishing tasks. To find out more about the varied flooring machinery we provide, please contact us today. We’d be happy to help with any enquiries.